Pages home > Boat Baths - Choosing and Fitting in Your bath room

Boat Baths - Choosing and Fitting in Your bath room

Banheiras
Just what is a Boat Bath
A spead boat bath is often a traditional bath without feet which goes along for the floor or maybe more usually stands with a plinth which is either glued or bolted towards the main the main bath. A speed boat bath have a plug and overflow in the center of the bath lengthwise which makes it a dual ended bath, occasionally boat baths have a plug hole that is certainly and in the midst of the bath widthways however, this is less usual. Boat baths usually rise up slightly at each side with the bath and still have a good edge that curves downwards on the middle (lengthwise). Boat baths are often roll top baths, this means that the extra edge in the bath includes a profile that approximates to some section from the circumference of the circle. Bateau baths are a type of boat bath containing bath feet rather than plinth.

Boat Bath Construction Types
Most contemporarily manufactured boat baths are among four main construction types: Certain, Stone Cast Resin, Fibreglass and Acrylic Sheeting. You can find bad and good quality baths in each of these categories of construction. Surefire has the good thing about sticking to the standard construction materials if that is what you want but is heavy, a as a result of floor iron boat bath may well weigh about 200-250kgs. Stone Cast Baths are lighter but still heavy, 100-150 kgs, they are very rigid but aside from this haven't any real advantages over a good quality acrylic or fibreglass bath, stone cast baths are made of a mixture of powdered mineral and some kind of resin that might in fact be acrylic hence the the top these baths is usually not so different as people imagine in the the top of a polymer bath. Fibreglass baths have a very resin and glass fibre body, much like some car bodies which is then coated by having an acrylic gel to offer and acrylic surface. Baths constructed such as this tend to be more rigid than equivalent acrylic sheet baths however are still light (40-60kgs). Acrylic sheet baths if sufficiently reinforced can match the rigidity and excellence of fibreglass and gel coat baths but may large expanses of acrylic sheeting may be more flexible than fibreglass equivalents.

Fitting Taps for your Boat Bath
Boat bath are generally roll top baths and therefore cannot have taps attached to the edge from the bath unless they've got a tap platform. A tap platform can be an area around the fringe of the bathtub that flattens out in order that tap holes can be drilled from the bath and taps mounted on its edge. Because boat baths will always be double ended baths the tap platform if you find the first is invariably in the heart of the bathtub over the overflow. Where there isn't tap platform you will ought to fit either attached to the wall or floor mounted taps. Floor mounted taps will be mounted on stand pipes, stand pipes cover the pipes carrying water towards the taps usually with chromed piping and therefore are robust enough to aid the extra weight from the taps. Stand pipes stay at home contrast to pipe shrouds (also known as bath legs, and not to become mistaken for legs that secure the bath, these are entirely different). Pipe shrouds are utilized when taps are mounted on the edge of the bath and so are that will offer an decorative cover for the water feeds and not to guide the weight of the taps. Pipe shrouds usually are designed so they really are extendable which enable it to fit on baths of your number of heights. Boat baths come in general relatively high, and if you are fitting pipe shrouds or standing your taps on stand pipes you are able to they're of sufficient height on your bath. Generally speaking for standpipes you should try to use standpipes which might be as high or older than the section of the bath by which they're going to stand. Usually this will mean using 700mm standpipes. It's also advisable to take care if fitting taps on standpipes to make sure that the reach from the spout will likely be sufficient to overpower the roll top regarding the bathtub. If in doubt both with height and reach try to find cranked leg taps, a cranked leg tap has a wiggle from the leg that both pushes the tap higher up and additional forward giving both extra height and reach.

Selecting a Waste Kit for Your Boat Bath
Because boat baths are likely to be considered a conventional type of bath they may be more often than not fitted having a traditional plug and chain waste kit. Usually pop-up or click-clack wastes can be fitted but there are particular issues to do with some pop-up and click-clack wastes the inability fit on baths beyond some thickness and you should look into the thickness in the bath in the overflow as well as the plug hole along with the maximum thickness the waste kit you are thinking about will accommodate, it really is less usual to get this challenge with chain wastes nevertheless the best advice is usually to source the bath and waste kit through the same supplier who should then accept responsibility for their compatibility. Even be aware that fitting waste/filler combinations that fill from your overflow can have there own issues especially with regards to the size the filler part of the waste outside the bath which in extraordinary instances might be too wide as well as to adjust to without clashing together with the roll in the side of the bath.

Exposed and Concealed Waste Kits
The main aspects of the waste kit will be the plug and overflow parts which can be visible on the medial side the bath, the overflow pipe and associated fittings externally the bathtub and the trap and waste pipe which might be underneath the bath. Usually just the overflow pipe and associated fittings will be visible because the trap and outlet waste pipe will probably be hidden inside the boat baths plinth. In fact if the bath will be installed against a wall then no plumbing external for the bath will be visible and you'll make use of a concealed waste kit, this is a waste kit where those external parts are plastic. On the other hand if the bath is out of the wall you will want an exposed overflow pipe, that is certainly engineered to be anticipated to remain visible and it is therefore decorative, usually chrome, nevertheless the trap and waste pipe could be plastic as they are usually hidden beneath the bath. There are 2 exceptions to take into consideration about these general scenarios, firstly whether or not the bath is against a wall the overflow pipe might be visible, specifically if the bath is against an extended wall so that you will could stand along with your shoulder against the same wall and look down relating to the bath and the wall, this is the judgment you need to make. Secondly although trap under the bath won't normally be visible you may find if the clearance under the bath is 120mm or fewer the one trap you can find that can fit will likely be an exposed, i.e. chrome, trap that's been designed specifically to the freestanding bath market.

Extended Overflow Pipes
All boat baths are double ended, that's, the plug hole and overflow will be in the center of the bath lengthwise. In most cases the plug hole although central lengthwise will probably be over for the back from the bath width wise, however in a small amount of cases the plug hole might be discovered to be from the dead core bath, that is certainly central both lengthwise and widthwise. If it is the truth many times that a standard sized overflow pipe will not reach far enough within the bath to join up to together with the waste pipe that extends below the plug hole. In the event this way you simply must fit an overflow extension pipe, such extensions hook up to the overflow pipe which has a compression fitting, that's, they simply push on and are sealed by the rubber gasket already fitted on the extension. That you will find to source this from your specialist in freestanding baths.

Keeping of the Waste Pipe
If the clearance under your boat bath is such you need to readily extra shallow trap you'll realize that the waste pipe that connect with the trap is going to be at roughly the same height as the overflow pipe and you will not be able to lead the waste pipe out the same manner because the overflow pipe also comes in since they would want to occupy the identical space. Rise no problem because trap will hook up with the waste pipe from the plug hole which has a captive nut that allows the trap to be positioned released at any angle then it could be positioned so that the outlet waste pipe will not restrict the overflow pipe. Having said that your plumber must be informed about this possiblity to ensure that no work is done laying underfloor waste pipes that can't connect track of the opening waste pipe from your trap

Dealing with your bath towards the floor
You should fix your bath firmly on the floor, essentially the most usual way to do this really is which has a boat bath is usually to glue the baths plinth on the floor using silicon resin or possibly a proprietary product for example Unibond's Forget about Nails. If you believe you may need to slowly move the bath just place a six inch bead of computer at each and every end to ensure if needed you'll be able to cut through it and move the bath, if weight loss likely the tub will not be moved put a bead everywhere in the lower bath.

Special Things to consider for Antique Boat Baths
You'll find special considerations should your bath is an antique, in particular the plug hole and/or overflow hole could possibly be greater than in the contemporary bath which may signify the conventional fittings that are great for to the within the bath will be not big enough so they drop straight with the hole. Apart from salvaging antique waste kits (who are not guaranteed to fit anyway) or having parts remanufactured there might not be a straightforward answer. Generally speaking one course of action is usually to avoid baths that have outsized plug or overflow holes.

Last updated 456 days ago by Banheira2